How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of special steps to install a second ignition key. It requires dealer service using a handheld computer dubbed Tech-2. Then it is necessary to purchase a new transponder. key need to be purchased.

It is recommended to rotate your keys in order that one does not wear out faster than the other. This will also ensure that your keys remain in good condition.

Replacement Case

As opposed to the traditional saab spare key keys of the past keys, the latest key fobs contain electronics that make it difficult to copy. This has made car theft much more difficult than it was twenty years ago. However, it also has made the replacement of lost keys a comparatively costly endeavor.

Every owner of a Saab 9-3 should have at least two working keys. It is costly to replace a lost key because it requires replacing the CIM module, and programming the locking cylinders. Dealers charge between $100 and $200 for this.

There are ways to cut down on these costs. Some parts providers can look up the code from an extra key (usually the same one that opens the doors and turns off the ignition) and cut a new key blade from metal for only a fraction of the dealer's cost. The key, however, must be the same as the original one in order to function within your car.

Follow these steps to replace the case. You'll require a flathead screwdriver along with some patience. With the screwdriver you can pull away the plastic and take out the emergency key. Once the case is open, remove the electronic components and place them into your new case. Place the key with the correct badge inside the case.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost component that can be replaced easily and quickly. This YouTube video by Cyclone Cyd shows how to replace the battery for the remote fob in just four simple steps. This tutorial should work for any modern saab key fob, though the process may vary slightly.

The first step is to locate the button that releases the backup key in the fob. This button is typically located on the back of your fob, just below the saab 93 key fob replacement Logo. Use a flathead screwdriver to insert the screwdriver into the small hole on this button. This will allow you to open the case of the fob to allow you to replace the battery.

Once you have installed the batteries CR1632, you can rebuild your remote key fob. You can then program it into your car. The entire process should take no more than a half hour at the most. It is a very simple procedure that doesn't require any special tools.

The procedure is a little more complicated if you lose your key, but it's possible. The dealer will need to read the car's VIN and then purchase a replacement key blade and TWICE module with the exact unique code. After that, they will have to cut the new key and then program it using the latest software tool known as MDI.

Key Replacement Fob

The key fob is the piece that locks and unlocks your car, it has a battery inside. The batteries are able to last for that is a long time, and they eventually die. This is a common problem that occurs with all vehicles, and the good news is that you can replace the batteries on most fobs, without replacing the whole case. Amazon sells replacement fobs with all the electronics in place. It is easy to remove the case and replace the batteries. It's important to note that you'll need to take out the emergency key first, and you can do this by inserting a small flathead screwdriver into the slot in the middle of the case. The case will split as you work the screwdriver all around it.

If you are about to replace your keys, make sure you have a spare, since this will cut down the total cost by a significant amount. If you have a spare you can request that the dealer cut an entirely new key and then program it into your car, which is much cheaper than replacing the entire key fob.

If you do not have a spare key you can add an additional key to your car, but this will require a lot of research and effort. The cost of adding a second key is several hundred dollars and it requires programming of the car's computer. This can be done by a professional, but it's an expensive option for the majority of owners.

Replacement Ignition

The modern SAAB 9-3 has a more sophisticated alarm system built on a keycode. If you lose only one key, it could be costly to replace it with another one, as the car has to have a specific computer installed and be programmed to accept a new key. Dealers can charge hundreds of dollars to program an entirely new key, when they are not able to complete the task.

Dealers will charge you a premium to replace your car's computer (also called the CIM or SAAB twice) in the event that you lose your only working key. Instead we can reprogram the EEPROM of your current car computer to prepare it to accept a second key, which will save you more than 50% of the amount you spend at a dealer.

If you have owned a 9-3 from SAAB for an extended period of time and you're aware of the ignition keys aren't very durable. If your ignition key is not working correctly, you should look into replacing it. They can become very sticky and the buttons can fall off. Luckily, replacing the ignition key isn't as complicated as it seems, and it can be done in a short time with the appropriate tools.